Toyota 120 Platforms Forum
Google only search Toyota120

Go Back   Toyota 120 Platforms Forum > Technical write ups > Mechanical

Closed Thread
Thread Tools Display Modes
Unread 07-27-2013, 04:23 PM   #1
michaelreed
Driver
 
michaelreed's Avatar
 
Join Date: Mar 2012
Posts: 203
Default V6 Valve cover gasket replacement

And so it begins. Would anybody like me to do a detailed write up of the process? I haven't seen any good ones for the 4th gen so I thought id ask before I get started.







I'm going to update this as I go to make it easier on me.

Parts needed:

L&R valve cover gasket 11213-AD010 & 11214-AD010
Toyota fipg 00295-00103

I also chose to do my spark plugs, pcv valve, clean the throttle body and clean the maf sensor.

Pcv valve 12204-31030
Denso iridium plugs ikh20-5344
Throttle body cleaner
Mass air flow sensor cleaner

Tools needed:

Ratchet
10mm socket
12mm socket
Philips screwdriver
8mm hex socket
Torque wrench
Extentions

First thing to do is remove engine cover. There are two 10mm nuts on top.



Next disconnect the negative battery cable from the terminal.



Next we have to remove the air intake duct. First, detach the ground wire from the hose. The tab just wiggles out of a rubber lip on the hose.



With a Philips or 10mm socket, loosen the hose clamps on the air intake duct. It takes a little finesse to get the duct off the air filter housing and fresh air inlet (fender side).



Unplug the connector attached to the mass air flow sensor. Unscrew two Philips screws and pull out the maf sensor. As mentioned this is good time to clean the sensor.





Next we need to disconnect the pcv fresh air inlet hose. Squeeze the clamp and pull the hose off. May take some convincing to get the hose off. It's located on the front of the air filter housing to the right of the mag sensor.



Loosen the hose clamp that connects the air filter housing to the throttle body with a 10mm socket/Philips.



Remove the two bolts that secure the air filter housing. There is one on the top right and one on the bottom left.





Disconnect the wiring harness clip from the air filter housing



And unplug this line from the back of it



You can then remove the air filter housing. Just lift up and pull it away from the throttle body.



Next we need to remove the upper intake manifold. There's quite a few hoses and connectors to remove so remember what you pulled off or label it.

Remove this fuel vapor feed hose and the vsv connector next to it. This on the drivers side of the manifold.



This vsv connector is on the opposite side. Remove it.



I couldn't get the coolant lines off the throttle body so I just removed it and set it aside. There are four bolts securing it to the intake manifold.



There are two clips on the back side of the manifold that are a royal pain to get off. There is a tab on each that you have to pull down on to release them. This is what the clips secure to. I couldn't get a photo while they were connected.



Next remove the three manifold brackets. Toyota refers to these as air surge tanks stays fyi.





Lastly, remove the 2 nuts and 4 bolts that secure the manifold in place. This is where you need the 8mm hex. Remove the intake manifold.



You'll want to cover the lower intake manifold so nothing falls in.
michaelreed is offline  
Unread 07-27-2013, 07:30 PM   #2
michaelreed
Driver
 
michaelreed's Avatar
 
Join Date: Mar 2012
Posts: 203
Default

You now have a clear view of the valve covers. Disconnect and remove your coil packs. Ill assume you know how to do this.

Now we need to remove the wiring harness from the valve covers.
You can CAREFULLY pry them up with a screwdriver or use and awl to release the retaining tabs inside.



Remove the 12 bolts holding the valve cover down and remove the valve cover.





Peel off the old gasket. Use a gasket scraper to remove the rtv from where the heads meet the timing cover.

Moving on to the valve cover. Clean it with brake cleaner and make sure there is no debris on the gasket surface.



Seat the gasket in the groove like so.



Now just put dabs of fipg where the timing chain cover meets the head. Torque the nuts and center bolts to 80in.lbs and the outer bolts to 84in.lbs.

Installation is reverse of removal. Just stay organized and you'll be gtg.
michaelreed is offline  
Unread 07-28-2013, 05:25 PM   #3
michaelreed
Driver
 
michaelreed's Avatar
 
Join Date: Mar 2012
Posts: 203
Default

Actually I think I "may" have figured it out. Pcv valve was stuck closed. Luckily I bought one and was going to replace it anyway. Could be wrong but that's my guess. May also be why when I pulled the covers it smelled like gas a little bit.

michaelreed is offline  
Unread 07-29-2013, 12:30 PM   #4
michaelreed
Driver
 
michaelreed's Avatar
 
Join Date: Mar 2012
Posts: 203
Default

I had oil on the cylinder #6 spark plug. Thought it was a head gasket at first but I wasn't missing coolant or misfiring like the other guys. I pulled my plugs and as you can see on the bottom plug, the oil is at the top of the plug. There was none at the bottom or on the electrode. I suspect it was a combination of the bad pcv valve and old gaskets

michaelreed is offline  
Closed Thread

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Head Gasket Blown - 2004 V6 Sledgehammer 4th Gen 4Runner & Hilux Surf 28 10-29-2016 06:00 PM
Valve cover gasket replacement. michaelreed 4th Gen 4Runner & Hilux Surf 23 04-13-2015 09:42 AM
Well.. It's a blown head gasket. michaelreed 4th Gen 4Runner & Hilux Surf 25 07-31-2013 07:49 AM
Broken TPMS Valve Stem Sledgehammer Suspension and Tires 8 08-29-2011 01:07 PM
Head Gasket Replacement. NewVillains 4th Gen 4Runner & Hilux Surf 2 02-20-2009 08:28 AM


All times are GMT -7. The time now is 02:28 PM.


Powered by vBulletin® Version 3.7.4
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
Copyright 2005-2013 Toyota120.com